manualshive.com logo in svg

Ness IDTECK iCON100, User Manual

Share
Download
Ness IDTECK iCON100 User Manual Download Page 11

 

 

 

101-000                                                 -11-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

3.3 OPTIONAL ACCESSORIES 

 

3.3.1 LCD DISPLAY MODULE 

 

You can connect an optional LCD display module to the NESS - iCON100 main control board. With 
a keypad, this allows you to setup all functions on the NESS - iCON100 manually. 

 

3.3.2 KEYPAD 

 

You can connect an optional keypad to the NESS - iCON100 main control board. With an LCD 
display module you can setup all functions to the NESS - iCON100 manually. 

 

4.  INSTALLATION REQUIREMENTS 

 
Installing the 

NESS - iCON100

 is a relatively easy task. It can be installed with common hand tools and 

readily available communications wire. This section provides information about wiring, wire runs and other 
information to make the installation quick and easy. 
 

4.1 CHECK POINTS BEFORE INSTALLATION 

 

4.1.1 CABLE / WIRE 

Good electrical connections will minimize line losses and prevent damage to the 

NESS - iCON100

 

control electronics. Use good quality wire that’s a proper thickness with durable insulation such as 
vinyl or PVC. It may be faster and much economical to run multiple, twisted pair cable rather than 
individual pairs. The following cable and wire thickness from the Belden Master Catalog 885 are 
adequate for most 

NESS - iCON100

 applications. These are offered as a reference only. 

 
Belden No. 9745      3 twisted pairs, 22 AWG, 7/30 stranded, unshielded, PVC insulation and jacket,   
 

 

 

14.7 ohms/1000 feet (about 300meter). 

Belden No. 9750      3 twisted pairs, 20 AWG, 10/30 stranded, unshielded, PVC insulation and jacket,   
 

 

 

10.3 ohms/1000 feet (about 300meter). 

  

Belden No. 8303 

3 twisted pairs, 22 AWG, 7/30 stranded, shielded, overall foil/braid shield, PVC 

insulation and jacket, 14.7 ohms/1000 feet (about 300meter). 

 

CONDUIT 

The 

NESS - iCON100

 does not normally require conduit. However, some locations may require 

conduit for wire protection. Check installation requirements and specifications for your site. 

 

COMMUNICATIONS WIRING 

NESS -iCON

 communication is required for using twisted pair wires. 

CAUTION: 

Distance can be reduced by surroundings. 

Summary of Contents for IDTECK iCON100





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands