manualshive.com logo in svg

Ness IDTECK iCON100, User Manual

Share
Download
Ness IDTECK iCON100 User Manual Download Page 28

 

 

 

101-000                                                 -28-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

7.5 ID REGISTRATION 

You can register the User ID into the NESS - iCON100. Select 

[SETUP MENU F3]

 -> 

[ID 

REGISTRATION]

 then follow the steps below. 

 

 
 
 
 
 
 
 
 
 

1. Registration by RF Cards   

 
 
 
 
 
 
 
 
 

2. Registration by Keypad   

 
 
 
 
 
 
 
 
 

 

1. ID [________]: The ID number consists of a 3-digit facility code from 000 to 255 and a 5-digit ID 
number from 00000 to 65535. The 8-digits ID number therefore cannot exceed 25565535. Enter the     
8-digit ID number then press the <ENT> key in the ID [________] field.   

Initial LCD Display 

NESS-iCON100 [F1] 

01/20  09:01:23 

Press <F3> then 

Select 

[

ID REGISTRATION] 

8 times <0> + <ENT> 

“MASTER ID” + <ENT> 

ID REGISTRATION

ID REGISTRATION  

 1:Card  2:Key 

‘ENT’ 

Scanning … 

    12345678 

  PW____ TS__ RD_ 

Approach card 

Reader1

‘1’ 

Password(4digits) + <ENT> 

Time Schedule codes + <ENT> 
Reader Usage codes + <ENT>

 

 

ID Registered 

Reg. completed 

  [________] 

  PW____ TS__ RD_ 

    12345678 

  PW____ TS__ RD_ 

ID(8digits) + <ENT>

‘2’ 

Password(4digits) + <ENT> 

Time Schedule codes + <ENT> 
Reader Usage codes + <ENT>

 

ID Registered 

Reg. completed 

Summary of Contents for IDTECK iCON100





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands