manualshive.com logo in svg

Ness IDTECK iCON100, User Manual

Share
Download
Ness IDTECK iCON100 User Manual Download Page 51

 

 

 

101-000                                                 -51-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 

 

 

 

 

 

9.4.7 INPUT AND DIP SWITCH TEST

 

 

 

 

 

 

 

 

 

 

 

9.4.8 COMMUNICATION TEST   

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 

Reader 1        
      00312345 

Card # 

Reader # 

INPUT   TEST 

 

☞

. When the reader has successfully read the card, the LCD will 

display the reader number and an 8 digit card number on the 
LCD. Press the <ESC> key to return to the setup menu. 

☞

. Press the <ENT> key for the input test.

 

☞

. The first 8 digits of the bottom line shows the status of the DIP 

switch for the communication ID setting and “1” indicates the 
switch ON position and “0” indicates the switch OFF position. The 
last 5 digits show the input status and “0” indicates the input port 
open circuit and “1” indicates the input port short to ground level. 
Press the <ESC> key to return to the setup menu.

 

INPUT  TEST 

11111111 

00000 

INPUT  

DIP S/W 

COMM test pass!! 

Press any key... 

TX data = 0       

COMM fail 

COMM  TEST 

 

☞

. Before this communication test, connect the RS232-RX and 

RS232-TX wires together. Then press the <ENT> key. 

☞

. 

This test is a loop test and the NESS - iCON100 sends a character to 
RS232-TX which checks whether the RS232-RX receives the character 
or not. If you have an error, please contact our service facility. 

☞

. After the test is done, the LCD will display “COMM test pass!!”. 

Press any key to return to the setup menu.

 

Summary of Contents for IDTECK iCON100





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands