manualshive.com logo in svg

Ness IDTECK iCON100, User Manual

Share
Download
Ness IDTECK iCON100 User Manual Download Page 36

 

 

 

101-000                                                 -36-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

9.1.9 SYSTEM INITIALIZE 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

9.1.10 CARD ID CLEAR 

 

 
 
 
 
 
 
 
 
 
 

9.1.11 TIME SCHEDULE CLEAR 

 
 
 
 
 
 
 
 
 
 

 

9.1.12 KEYPAD INPUT SETTING 

 

 

 

 

 

 

 

SYS INITIALIZE 

 1 – Yes, 0 - No 

SYS INITIALIZE 

System 

Initializing.. 

☞

. This operation will initialize the NESS - iCON100. Press <the 

ENT> key, if an initialization is needed (first time installation or 
resetting in the event of a malfunction).   

CAUTION: Initializing will erase all stored data in the memory. 

☞

. Press the<1> key to initialize or the <0> key to cancel the 
operation.

☞

. This message appears while the system is being initialized. 

After the initialization, the NESS iCON100 will return to the 

setup menu.

 

CARD ID CLEAR 

1 - Yes, 0 - No 

CARD ID CLEAR 

TIME SCHE CLEAR 

 

TIME SCHE CLEAR 
1 - Yes, 0 - No 

☞

. Press the <ENT> key then press the <1> key to clear all User Ids 

(Card Ids) from memory, or the <0> key to cancel the operation. 

 
CAUTION: Before you clear all User IDs, make sure that the 

registered User IDs are no longer used. 

 

 

☞

. Press the <ENT> key then press the <1> key to clear all T/S form 

memory, or the <0> key to cancel the operation. 

 
CAUTION: Before you clear all T/S, make sure that the stored 

T/S is no longer used otherwise you may lose all 
stored T/S in the memory. 

 

RF PIN INPUT  

->ENABLE 

RF PIN INPUT  

  DISABLE 

☞

. This function is to set to DISABLE/ENABLE the keypad inputs 

from the Proximity and Keypad Readers. The keypad inputs are 
DISABLED by default. If you install a Keypad Reader (8bit 
burst format) and set this mode to ENABLE, you can access the 
Door by pressing an 8digit User ID from the keypads. 
Press the <ENT> key and press the <4> or <6> key to select -
>ENABLE then press the <ENT> key to setup this function. 

Summary of Contents for IDTECK iCON100





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands