NEC mPD780204 User Manual Download Page 340

Page: 340 / 418

340

CHAPTER 16 INTERRUPT AND TEST FUNCTIONS

User’s Manual U11302EJ4V0UM

(1) Interrupt request flag registers (IF0L, IF0H)

The interrupt request flag is set to 1 when the corresponding interrupt request is generated or an instruction

is executed. It is cleared to 0 when an instruction is executed upon acknowledgment of an interrupt request

or upon application of RESET.

IF0L and IF0H are set with a 1-bit or 8-bit memory manipulation instruction. If IF0L and IF0H are used as

a 16-bit register IF0, use a 16-bit memory manipulation instruction for setting.

RESET input clears these registers to 00H.

Figure 16-2. Format of Interrupt Request Flag Register

Note

WTIF is the test input flag. A vectored interrupt request is not generated.

Cautions 1. The TMIF4 flag is R/W enabled only when the watchdog timer is used as an interval timer.

If the watchdog timer is used in watchdog timer mode 1, set the TMIF4 flag to 0.

2. Always set bits 6 and 7 of IF0H to 0.

3. When an interrupt is acknowledged, the interrupt request flag is automatically cleared,

and then servicing of the interrupt routine is started.

4. When the interrupt request flag register is manipulated (including by a 1-bit memory

manipulation instruction), if an interrupt request corresponding to another flag in the

same register is generated, the flag corresponding to that interrupt request may not be

set to 1.

TMIF0

IF0H

<5>

<4>

<3>

<2>

<1>

<0>

xxIF

Interrupt request flag

FFE1H

TMIF1

ADIF

TMIF2

KSIF

WTIF

Note

00H

R/W

No interrupt request signal

Interrupt request signal is generated: Interrupt request state

TMIF4

IF0L

<7>

<6>

<5>

<4>

<3>

<2>

Symbol

<1>

<0>

FFE0H

PIF0

PIF2

PIF1

PIF3

CSIIF0

CSIIF1

TMIF3

Address

After reset

R/W

00H

R/W

Summary of Contents for mPD780204



































































































































































































































































































































































































































Search results

Summary of Contents for mPD780204

Reviews:

Related manuals for mPD780204

Brands by name

Popular brands

NEC mPD780204, User Manual

Search results

Summary of Contents for mPD780204

Reviews:

Related manuals for mPD780204

Brands by name

Popular brands