manualshive.com logo in svg

NEC Express5800/120Eg, User Manual, Page: 5 / 332

Share
Download
NEC Express5800/120Eg User Manual Download Page 5

NOTE:

    This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.    These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.    This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications.    Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

CE Statement

Warning:

This is a Class A product.    In domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures (EN55022).

BSMI Statement

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments