NEC Express5800/120Eg User Manual Download Page 149

Page: 149 / 332

Installing the Operating System with Express Setup 5-49

HostRAID Setup Flow

The flowchart below shows the HostRAID system setup procedure.

Start

Enable the HostRAID

feature and create RAID by

using BIOS setup utility

Refer to Chapter 4

Install driver

(install OS).

See Appendix D or E of
this guide.

Update system.

See this chapter.

Install ASMBE.

See ASMBE User's
Guide

Install Standby/Hibernation

Lock driver.

See appendix of ASMBE
User's Guide

End

*1 You can create RAID by using the NEC EXPRESSBUILDER. In this case, only you need to do is to set the

HostRAID feature to "Enabled" by using BIOS setup utility.

*2 ASMBE User's Guide: Adaptec Storage Manager

- Browser Edition User's Guide.

You may view or print the Adaptec Storage Manager™ - Browser Edition User's Guide from the
NEC EXPRESSBUILDER CD-ROM.

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Search results

Summary of Contents for Express5800/120Eg

Reviews:

NEC Express5800/120Eg, User Manual, Page: 149 / 332

Search results

Summary of Contents for Express5800/120Eg

Reviews: