manualshive.com logo in svg

NEC Express5800/120Eg, User Manual, Page: 180 / 332

Share
Download
NEC Express5800/120Eg User Manual Download Page 180

7-10  Maintenance

 

7. 

Follow the guideline showed in the bottom of the screen and press ESC to show the End
user Menu showed below.

Please choose a function by the arrow key and push Enter key.

Enduser Menu

TeDoLi (TEst & Diagnosis On Linux) Ver001.00 (Build020901.1.1m)

<Test Result>

<Device List>
<Log Info>
<Option>
<Reboot>

<Test Result> shows the screen of the diagnosis completed aforementioned.

<Device List> shows the information of all the devices connected.

<Log Info> 

shows the log information and error messages of the diagnosis. It can be
saved to a floppy disk.    To save the log information to a floppy disk,
insert a formatted floppy disk to a floppy disk drive and select
<Save[F]>.

<Option>

change where to output log

<Reboot>

Restarts the Express Server.

 

8. 

Select <Reboot> in the End user Menu above.

The Express Server restarts, and NEC EXPRESSBUILDER boot the system.

 

9. 

Exit the NEC EXPRESSBUILDER, and remove the CD-ROM from the CD-ROM drive.

 

10. 

Turn off the server and unplug the power cord from the receptacle.

 

11. 

Reconnect all the LAN cables to the server.

 

12. 

Plug the power code.

This completes the System Diagnostics.

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments