NEC Express5800/120Eg User Manual Download Page 27 | Manualshive

Page: 27 / 332

NEC Express5800/120Eg User Manual Download Page 27

Notes on Using Your Server 1-11

USER SUPPORT

Before Asking for Repair, do the following when the server appears to fail:

1.

Check if the power cord and the cables to other devices are properly connected.

2.

See Chapter 8 to find if your problem fits the description. If it does, take the
recommended measure for it.

3.

Check if the software required for operation of the server is properly installed.

If the server still appears to fail after you have taken the above actions, consult with your sales agent
immediately. Take notes on lamp indications of the server and alarm indications on the display
unit before consultation, which may provide a significant help to your sale agent.

«
...
25
26
27
28
29
...
»

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments