manualshive.com logo in svg

NEC Express5800/120Eg, User Manual, Page: 234 / 332

Share
Download
NEC Express5800/120Eg User Manual Download Page 234

9-16  Upgrading Your Server

Installation

 

1. 

See the section "Preparing for Installation and Removal" described earlier to prepare.

 

2. 

Remove the side cover.

 

3. 

Remove the two screws fixing the dummy cover.

 

4. 

Pull out the dummy cover toward you carefully.

NOTE:

 When installing a full-height device, remove two dummy

covers.

 

5. 

Fix the rails coming with the server to the 5.25-inch device by using the four screws
coming with the device.

IMPORTANT:

„

 

Always use the screws coming with the 5.25-inch device.    Using
longer screws or those of different diameter may cause the device to
be broken.

„

 

When installing a double-height device, use the DLT device rails
that come with the server.

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments