manualshive.com logo in svg

NEC Express5800/120Eg, User Manual, Page: 311 / 332

Share
Download
NEC Express5800/120Eg User Manual Download Page 311

Appendix F

Installing Windows 2000

This section describes the procedures for installing Windows 2000 without using Express Setup
tool.

BEFORE INSTALLING WINDOWS 2000

Please read carefully the following information BEFORE commencing your Windows 2000
Installation.

Optional Board Supported by NEC EXPRESSBUILDER

The NEC EXPRESSBUILDER CD-ROM attached to your system supports the following optional
boards;

„

 

Supporting installation of OS in NEC EXPRESSBUILDER

–

 

N8103-65F SCSI Controller

–

 

N8103-75F SCSI Controller

–

 

N8103-95 SCSI Controller

–

 

N8103-78F Disk Array Controller (SATA)

–

 

N8103-80F Disk Array Controller (SCSI 1ch)

–

 

N8103-89 Disk Array Controller (SATA)

–

 

SATA HostRAID (Onboard Adaptec HostRAID controller)

„

 

Other optional boards

–

 

N8103-56F SCSI Controller

Installing Service Pack

You can install the Service Pack on the server.    When the Service Pack is not attached to your
system, prepare it by yourself.

IMPORTANT:

 Be sure to confirm the following items before

applying Service Pack to your system.
This system does not support Windows 2000 Service Pack 1 - 3.
If you install Windows 2000 CD-ROM which contains Service Pack 4
to your system, you do not have to apply Service Pack 4 again.

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments