NEC Express5800/120Eg User Manual Download Page 81

Page: 81 / 332

Configuring Your Server 4-13

Option

Parameter

Description

Your Setting

Secure Mode

Timer

[ 1 Minute]

2 Minutes

5 Minutes

10 Minutes

20 Minutes

60 Minutes

120 Minutes

Set the period from no input from the

keyboard or mouse to the point at

which the system enters into the

secure mode.

Security Hot Key

CTRL-ALT-

[L]

Specify the hot key to invoke secure

mode features. Pressing the assigned

key along with

Ctrl

and

Alt

invoke

secure mode. This option is enabled

when User Password is set.

Secure Mode Boot

[Disabled]

Enabled

Specify whether the system boots in

secure mode. This option is enabled

when User Password is set.

The keyboard will remain locked until

a password is entered.

Front Panel Switch

Inhibit

[Disabled]

Enabled

Enables or disables the POWER

switch. If "Enabled" is selected,

power-off with the POWER switch

becomes unavailable after OS boot-

up. (Forced shut down also becomes

unavailable. Forced shut down is a

feature to shut down by pressing the

POWER switch for at least four

seconds.)

NMI Control

Disabled

[Enabled]

Enables or disables the DUMP switch

on the front panel.

[ ]: Factory-set

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Search results

Summary of Contents for Express5800/120Eg

Reviews:

NEC Express5800/120Eg, User Manual, Page: 81 / 332

Search results

Summary of Contents for Express5800/120Eg

Reviews: