Home
/
NEC
/
Express5800/120Eg
/
User Manual

NEC Express5800/120Eg, User Manual, Page: 201 / 332

Share

Page: 201 / 332

NEC Express5800/120Eg User Manual Download Page 201

Troubleshooting 8-19

Unable to update the system:

T

Are you trying to update the system without applying Service Pack or with Service
Pack 1, 2, or 3?

→

Without applying Service Pack and applying Service Pack 1, 2, or 3 to this system
are not supported.

You have to apply Service Pack 4 to update the system.

If you use Windows 2000 CD-ROM which includes Service Pack 4 to install
Windows 2000 on your system, you do not have to apply Service Pack 4 again
when you update the system.

The system does not restart automatically when a stop error occurs, though the system is
adjusted to automatically restarting:

→

When the system does not restart automatically, restart it manually.

The system restarts automatically when a stop error occurs, though the system is NOT
adjusted to automatically restarting:

→

There is no problem about this issue.
Check the System Event Log to confirm that STOP error occurred.

Cannot turn the power OFF at the blue screen:

→

If you want to turn off the power at the blue screen, execute forced shutdown
(forced shutdown: continue to press POWER switch for 4 seconds). The power
will not be turned off if you press the switch for less than 3 seconds.

«
...
199
200
201
202
203
...
»

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments