manualshive.com logo in svg

NEC Express5800/120Eg, User Manual, Page: 160 / 332

Share
Download
NEC Express5800/120Eg User Manual Download Page 160

6-10    Installing and Using Utilities

CONFIGURATION DISKETTE CREATOR

"Configuration Diskette Creator" is a tool to create [Configuration Diskette] that is used for
configuring the server with the Express Setup (see Chapter 5 for details).

If you use the Configuration Diskette created by the Express Setup and Configuration Diskette
Creator to operate the setup, you can setup from the installation of OS to several utilities
automatically except for a few key input to confirm the specification. Also, you can install the
system with the same specification as before when re-installing the system. We recommend you to
create [Configuration Diskette] to setup the servers from NEC EXPRESSBUILDER.

IMPORTANT:

 You can not create [Configuration Diskette] for

Microsoft Windows Server 2003 x64 Editions.

NOTE:

 You can install Windows Server 2003 and Windows 2000

without [Configuration Diskette]. Also, you can modify/newly create
[Configuration Diskette] during the setup with NEC
EXPRESSBUILDER.

Creating Configuration Diskette

This section describes about specifying setup information that is necessary for OS installation and
creating [Configuration Diskette]. Follow the procedure below.

NOTE:

 In the procedure below, the folder name that is specified when

installing Trekking command is assumed as [Configuration Diskette
Creator].

 

1. 

Start the OS.

 

2. 

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Master Control Menu will appear.

 

3. 

Right-click on the screen or left-click [Software Setup]. The menu will appear.

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments