manualshive.com logo in svg

NEC Express5800/120Eg, User Manual, Page: 232 / 332

Share
Download
NEC Express5800/120Eg User Manual Download Page 232

9-14  Upgrading Your Server

 

10. 

Connect the interface cable and power cables. See Chapter 10 for details.

IMPORTANT:

„

 

Keep the socket cover removed from the power cable connector or
interface cable connector for future use.

„

 

For serial ATA hard disk drives, use the relay cable connector that
comes with the optional serial ATA cable as shown figure below.

 

11. 

Reinstall the side cover.

 

12. 

Close the front door.

Removal

Remove the hard disk in the reverse procedure of the installation.

In the disk array configuration, the auto rebuild function can be used.    The auto rebuild function
can record the information saved in a defected hard disk into the new replaced disk to recover the
server to the state before the occurrence of the fault.

The auto rebuild function is valid for disk arrays set to RAID1, RAID5, or RAID10.

Refer to the manual supplied with your RAID controller for detail explanation.

Relay cable
connector

Summary of Contents for Express5800/120Eg













































































































































































































































































































































Reviews:

No comments