Nashuatec Aficio 9005 Operating Instructions Manual Download | Manualshive

Page: 148 / 177

background image

Settings You Can Change with User Tools

135

4

❖

❖

❖

❖

Panel Features Default

You can specify the other tab function that is selected automatically just after
the machine is turned on or when modes are cleared.

❖

❖

❖

❖

Image Adjustment Priority

You can select the function that is priority detected in Image Adjustment
mode.

❖

❖

❖

❖

Tone: Original Remains

The beeper (key tone) sounds when you forget to remove originals from the
exposure glass after copying.

Note

❒

If the “Panel Tone” in User Tools (System Settings) is “Off”, the beeper
does not sound irrespective of the “Tone: Original Remains” setting. See
“Panel Tone”,

General Settings Guide

.

❖

❖

❖

❖

Job End Call

You can select to have the beeper sound when copying is complete.

Note

❒

If the “Panel Tone” in User Tools (System Settings) is “On”, the machine
beeps to notify you if it did not complete a job, for reasons such as: copying
was interrupted, the paper tray ran out of paper or a paper jam occurred.

❖

❖

❖

❖

Customize Function: Copy

You can register frequently used functions for copying in function keys. You
can also change registered functions.

❖

❖

❖

❖

Customize Function: Store Document Server

You can register frequently used functions for storing data in the Document
Server in function keys. You can also change registered functions.

❖

❖

❖

❖

Customize Function: Print Document Server

You can register frequently used functions for printing data stored in the Doc-
ument Server in function keys. You can also change registered functions.

❖

❖

❖

❖

Special Original Display Defaults

You can have special originals shown on the initial display.

BelliniC2_GBcopy_F_FM.book Page 135 Wednesday, December 11, 2002 3:47 PM

«
...
146
147
148
149
150
...
»

Summary of Contents for Aficio 9005


















































































































































































Reviews:

No comments

Related manuals for Aficio 9005

Brand: Canon Pages: 58

image Prograf iPF680 Series

Brand: Canon Pages: 132

Brand: Canon Pages: 44

imageClass LBP6230dw

Brand: Canon Pages: 16

Brand: Canon Pages: 2

imageprograf IPF785

Brand: Canon Pages: 42

Brand: Canon Pages: 148

Color Bubble Jet BJC-8200

Brand: Canon Pages: 6

Color Bubble Jet BJC-1000 Series

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Color Bubble Jet BJC-8200

Brand: Canon Pages: 105

Brand: Canon Pages: 2

Brand: Canon Pages: 68

Brand: Canon Pages: 4

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands