Nashuatec Aficio 9005 Operating Instructions Manual Download | Manualshive

Page: 157 / 177

background image

User Tools (Copier/Document Server Features)

144

4

❖

❖

❖

❖

Superimpose

You can have page numbers printed as a negative where they overlap black
parts of the image.

Input/Output

❖

❖

❖

❖

SADF Auto Reset

When you set one original at a time in the ADF, the Auto Feed indicator lights
for a selected time after an original is fed, showing it is ready for another orig-
inal.

Note

❒

You can adjust this time from 3 seconds to 99, in 1 second increments.

❖

❖

❖

❖

Eject Copy Face Up/Down in Glass

You can specify the way copies are delivered when copying an original from
the exposure glass.

❖

❖

❖

❖

Auto Sort

You can have Sort mode selected when the machine is turned on or reset, or
if the mode is cleared.

❖

❖

❖

❖

Memory Full Auto Scan Restart

If memory becomes full while scanning, the machine can make copies of those
already scanned, and then automatically resume scanning remaining origi-
nals.
You can enable or disable this function.

Note

❒

If you select

[

Off

]

:

• When memory becomes full, the machine stops operations allowing

you to remove copies delivered to the output tray.

❒

If you select

[

On

]

:

• You can leave the machine unattended to make all the copies, but result-

ing pages will not be sequentially ordered.

❖

❖

❖

❖

Sort/Stack Shift Tray Setting

You can select to turn Shift Tray Setting on or off in sort or stack mode.

❖

❖

❖

❖

Insert Separation Sheet

You can set the number of sets between Separation Sheets.

Note

❒

You can set the number from 1 set to 999 sets.

BelliniC2_GBcopy_F_FM.book Page 144 Wednesday, December 11, 2002 3:47 PM

«
...
155
156
157
158
159
...
»

Summary of Contents for Aficio 9005


















































































































































































Reviews:

No comments

Related manuals for Aficio 9005

Brand: Zeka Pages: 54

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: Sagem Pages: 83

Brand: Xerox Pages: 2

Brand: Xerox Pages: 11

Brand: Xerox Pages: 192

Brand: Xerox Pages: 10

Brand: Xerox Pages: 15

WORKCENTRE 7425

Brand: Xerox Pages: 88

Brand: Xerox Pages: 10

Brand: Xerox Pages: 33

C123 Copycentre

Brand: Xerox Pages: 154

WorkCentre 5845

Brand: Xerox Pages: 14

Brand: Xerox Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands