Nashuatec Aficio 9005 Operating Instructions Manual Download

Page: 83 / 177

Copying

CCCC

Press

[

Front and Back

→

2 Sided

]

Reference

To change the orientation of original and copy, press

[

Orientation

]

. See p.56

“Originals and copy orientation”.

DDDD

Place originals, and press the

{{{{

Start

}}}}

key.

Booklet

❖

How to fold copies to make a booklet

Fold the copy so that a crease is in the center and open as shown in the follow-
ing illustrations:

Open to left

Open to right

Note

❒

In this mode, the machine automatically sets the reproduction ratio to match
the paper size and copies the originals together onto the paper.

Reference

You can erase a 3 mm (0.1 inch) boundary margin around all four edges of
originals in Combine mode. See p.137 “Erase Original Shadow in Combine”.
You can insert lines to separate images. See p.139 “Separation Line in Com-
bine”

AAAA

Set the orientation with the User Tools.

Reference

p.140 “Orientation: Booklet, Magazine”

BBBB

Press

[

Dup./Combine/Series

]

CCCC

Press

[

Book

]

BelliniC2_GBcopy_F_FM.book Page 70 Wednesday, December 11, 2002 3:47 PM

Summary of Contents for Aficio 9005


















































































































































































Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands

Nashuatec Aficio 9005, Operating Instructions Manual

Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands