Nashuatec Aficio 9005 Operating Instructions Manual Download | Manualshive

Page: 20 / 177

background image

7

1. Placing Originals

Originals

Sizes and Weights of Recommended Originals

❖

❖

❖

❖

Metric version

❖

❖

❖

❖

Inch version

Non-recommended originals for the Auto Document Feeder (ADF)

Setting the following types of originals in the ADF can cause misfeeds or dam-
age to the originals. Place these kinds of originals on the exposure glass instead.
• Originals of inappropriate weight or size, see above
• Stapled or clipped originals
• Perforated or torn originals
• Curled, folded, or creased originals
• Pasted originals
• Coated originals, such as thermal fax paper, art paper, aluminum foil, carbon

paper, or conductive paper

Where original is set

Original size

Original weight

Exposure glass

Up to A3

--

Auto Document Feeder
(ADF)

1-sided originals:

A3

L

– A5

KL

52 – 128 g/m

2

2-sided originals:

A3

L

– A5

KL

52 – 105 g/m

2

Thin Paper mode:

A3

L

– A5

KL

40 – 128 g/m

2

Where original is set

Original size

Original weight

Exposure glass

Up to 11"

×

17"

--

Auto Document Feeder
(ADF)

1-sided originals:

11"

×

17"

L

– 5

1

/

2

"

×

8

1

/

2

"

KL

14 – 34 lb. Bond

2-sided originals:

11"

×

17"

L

– 5

1

/

2

"

×

8

1

/

2

"

KL

14 – 28 lb. Bond

Thin Paper mode:

11"

×

17"

L

– 5

1

/

2

"

×

8

1

/

2

"

KL

11 – 34 lb. Bond

BelliniC2_GBcopy_F_FM.book Page 7 Wednesday, December 11, 2002 3:47 PM

«
...
18
19
20
21
22
...
»

Summary of Contents for Aficio 9005


















































































































































































Reviews:

No comments

Related manuals for Aficio 9005

Brand: NCR Pages: 36

Brand: NCR Pages: 206

Brand: NCR Pages: 138

Brand: Datamax Pages: 26

Brand: Lexmark Pages: 11

Brand: Parkside Pages: 176

VarioPrint 4110

Brand: Oce Pages: 216

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: Lexmark Pages: 2

Brand: HandTop Pages: 97

Brand: Oki Pages: 56

Brand: Triumph Adler Pages: 139

Brand: Xerox Pages: 342

Brand: Fujitsu Pages: 126

Brand: Fujitsu Pages: 123

Brand: Fujitsu Pages: 146

Brand: Fujitsu Pages: 146

Brand: Fujitsu Pages: 182

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands