Nashuatec Aficio 9005 Operating Instructions Manual Download

Page: 31 / 177

Placing Originals

Thin mode

Use Thin mode for copying thin originals using the ADF.

AAAA

Press

[

Special Original

]

Note

❒

You can also set to display

[

Thin Paper

]

in initial settings. See p.134 “Special

Original Display”.

BBBB

Press

[

Thin Paper

]

, and then

[

]

CCCC

Place originals face up into the ADF.

DDDD

Press the

{{{{

Start

}}}}

key.

Placing custom size originals

When placing custom size originals in the ADF, specify the size of the originals.

Note

❒

Paper with a vertical length of 128–297 mm (5.1" – 11.6") and a horizontal
length of 128–432 mm (5.1" – 17.0") can be placed with this function.

AAAA

Press

[

Special Original

]

Note

❒

You can also set to display

[

Custom Size

]

in initial settings. See p.134 “Spe-

cial Original Display”.

BBBB

Press

[

Custom Size

]

, and then

[

]

CCCC

Enter the horizontal size of the original using the number keys, and then
press the

{{{{

}}}}

key.

Note

❒

If you make a mistake, press

[

Clear

]

, and then enter the value again.

BelliniC2_GBcopy_F_FM.book Page 18 Wednesday, December 11, 2002 3:47 PM

Summary of Contents for Aficio 9005


















































































































































































Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands

Nashuatec Aficio 9005, Operating Instructions Manual

Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands