Nashuatec Aficio 9005 Operating Instructions Manual Download Page 4 | Manualshive

Page: 4 / 177

background image

Introduction

This manual contains detailed instructions on the operation and maintenance of this machine. To get
maximum versatility from this machine all operators should carefully read and follow the instructions in
this manual. Please keep this manual in a handy place near the machine.

Notes

Some illustrations may be slightly different from your machine.

Certain options may not be available in some countries. For details, please contact your local dealer.

Warning:

Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.

Notes:

The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual. (For details,

⇒

p.2 “Machine Types”.)

•

Type1: IS2090

•

Type2: IS2105

Certain types might not be available in some countries. For details, please contact your local dealer.

Two kinds of size notation are employed in this manual. With this machine refer to the metric version.

For good copy quality,Infotec recommends that you use genuine Infotec toner.

Infotec shall not be responsible for any damage or expense that might result from the use of parts other
than genuine Infotec parts in your Infotec office product.

Power Source

220 - 240V, 50/60Hz, 16A

Please be sure to connect the power cord to a power source as above. For details about power source,
see “Power Connection” in General Settings Guide.

This information is based on our present state of knowledge and is intended to provide general notes
on our products and their uses.

It should not therefore be construed as guaranteeing specific properties of the products described or
their suitability for particular applications.

Any existing industrial property rights must be observed. The quality of our products is guaranteed un-
der our General Conditions of Sale.

For safe and correct use of this machine, please be sure to read the Safety Information in the General
Settings Guide before you use it.

BelliniC2_GBcopy_F_FM.book Page 1 Wednesday, December 11, 2002 3:47 PM

«
...
2
3
4
5
6
...
»

Summary of Contents for Aficio 9005


















































































































































































Reviews:

No comments

Related manuals for Aficio 9005

MultiPASS L6000

Brand: Canon Pages: 251

MultiPASS C5500

Brand: Canon Pages: 24

MultiPASS L6000

Brand: Canon Pages: 24

Laser Class 700 Series

Brand: Canon Pages: 221

Brand: Canon Pages: 149

Brand: Canon Pages: 60

Brand: Lanier Pages: 4

KXPX2M - HOME PHOTO PRINTER

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 9

Jetwriter KX-CL500

Brand: Panasonic Pages: 32

Brand: TE Connectivity Pages: 2

Brand: TE Connectivity Pages: 2

DocuPrint 4050 NPS

Brand: Xerox Pages: 248

Brand: Kyocera Pages: 2

Brand: Gerber Pages: 163

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands