Nashuatec Aficio 9005 Operating Instructions Manual Download Page 116

Page: 116 / 177

Copy Functions

103

GGGG

Press

[

Program

]

, and then press the stamp number (1–5) you want to pro-

gram.

Note

❒

Stamp numbers with

already have settings made for them.

❒

If the stamp number is already being used, the machine will ask you if you
want to overwrite it — press

[

Yes

]

[

]

HHHH

Enter the user stamp name using the letter keys on the control panel. You
can register up to 10 characters.

Reference

“Entering Text”,

General Settings Guide

IIII

Enter the horizontal size of the stamp (up to 17 inches) using the number
keys, and then press

[

]

JJJJ

Enter the vertical size (up to 11.7 inches) in the same way as step

IIII

KKKK

Place the user stamp on the exposure glass, and then press

[

Start Scanning

]

The original will be scanned, and the stamp will be registered.

Note

❒

Originals cannot be scanned from the ADF when programming the user
stamp.

LLLL

Press

[

Exit

]

To delete the user stamp

Important

❒

You cannot restore a deleted stamp.

AAAA

Make sure the machine is in Copy mode.

BBBB

Press the

{{{{

User Tools

}}}}

key.

CCCC

Press

[

Copier/Document Server Features

]

DDDD

Press

[

Stamp

]

EEEE

Press

[

User Stamp

]

FFFF

Press

[

Program/Delete Stamp

]

BelliniC2_GBcopy_F_FM.book Page 103 Wednesday, December 11, 2002 3:47 PM

Summary of Contents for Aficio 9005


















































































































































































Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands

Nashuatec Aficio 9005, Operating Instructions Manual

Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands