Nashuatec Aficio 9005 Operating Instructions Manual Download | Manualshive

Page: 58 / 177

background image

Copy Functions

45

2

Sort

Each time copies of a set or those of a different job are delivered, the next copy
set is shifted when delivered, so that you can separate sets or jobs.

Note

❒

You can select whether to shift or not. See p.144 “Sort/Stack Shift Tray Set-
ting”.

Reference

For setting conditions, see p.144 “Memory Full Auto Scan Restart”, p.144
“Sort/Stack Shift Tray Setting”, and p.132 “Auto Tray Switching”.

AAAA

Press

[

]

.

BBBB

Enter the number of copy sets using the number keys.

Note

❒

The maximum number of sets is 9999.

❒

To confirm the type of finishing, press the

{{{{

Sample Copy

}}}}

key. See p.46

“Sample copy”.

CCCC

Place originals, and then press the

{{{{

Start

}}}}

key.

Note

❒

When placing an original on the exposure glass, start with the first page to
be copied. When placing an original in the ADF, set so that the last page is
on the bottom.

❒

When placing an original on the exposure glass or in the ADF using batch
and SADF mode, press the

{{{{

#

}}}}

key after all the originals have been

scanned.

2

1

3

3

2

1

32

1

32

1

BelliniC2_GBcopy_F_FM.book Page 45 Wednesday, December 11, 2002 3:47 PM

«
...
56
57
58
59
60
...
»

Summary of Contents for Aficio 9005


















































































































































































Reviews:

No comments

Related manuals for Aficio 9005

ExpressCard 2000

Brand: Magtek Pages: 25

Brand: Valentin Pages: 96

imageRUNNER ADVANCE DX 6870i

Brand: Canon Pages: 115

imagerunner advance C5550i

Brand: Canon Pages: 1556

VersaLink C405/N

Brand: Xerox Pages: 256

Brand: Cycjet Pages: 26

Brand: Savin Pages: 4

Brand: VASTEX Pages: 8

Brand: Brady Pages: 48

Brand: Astro Machine Pages: 5

Brand: Aficio Pages: 92

magicolor 2430 DL

Brand: Konica Minolta Pages: 140

Workio DP-8016P

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands