Nashuatec Aficio 9005 Operating Instructions Manual Download

Page: 47 / 177

Copying

❖

Text/Photo

Select Text/Photo when originals contain photographs or pictures with text.

❖

Pale

Select this mode for originals that have light lines written in pencil, or for
faintly copied slips. Faint lines will be clearly copied.

❖

Generation

If originals are copies (generation copies), copy image can be reproduced
sharply and clearly.

❖

Dark Background

When you copy originals with dark background such as color tab stock (or-
ange, green, or blue), you can remove the background color in three levels.

Note

❒

[

Dark Background

]

appears only when you set Dark Background to

[

]

and

Original Type Display to

[

Hide

]

with the User Tools. See p.133 “Dark Back-

ground” and p.134 “Original Type Display”.

❒

If you select this mode, the auto image density function is disabled, but

[

Lighter

]

[

Darker

]

is enabled.

Reference

You can hide the original type display. See p.131 “Original Type Priority”.
You can set the picture quality for each original type. See p.133 “General Fea-
tures - Image Adjustment”.

AAAA

Press the appropriate key to select the original type.

BelliniC2_GBcopy_F_FM.book Page 34 Wednesday, December 11, 2002 3:47 PM

Summary of Contents for Aficio 9005


















































































































































































Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands

Nashuatec Aficio 9005, Operating Instructions Manual

Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands