Nashuatec Aficio 9005 Operating Instructions Manual Download

Page: 36 / 177

Basic Procedure

Auto Start

If you press the

{{{{

Start

}}}}

key during the warm-up period, the

{{{{

Start

}}}}

key will blink

and your copies will be made as soon as warm-up finishes.

AAAA

Make any adjustments to copy settings during the warm-up period.

BBBB

Place originals.

CCCC

Press the

{{{{

Start

}}}}

key.

Copying Starts automatically when the

{{{{

Start

}}}}

key indicator flashes red and

green indicating copy-readiness.

Interrupt Copy

Use this function to interrupt a long copy job to make urgently needed copies.

Note

❒

The procedure for making interrupt copies depends on the kind of operation
the machine is currently carrying out.

❒

You can use Document Server mode during Interrupt Copy.

❒

The previous copy job settings will be restored and the machine will continue
copying from where it left off.

AAAA

Press the

{{{{

Interrupt

}}}}

key.

When the machine stops scanning

Remove copied originals and place originals you want to copy.

Press the

{{{{

Start

}}}}

key.

The machine starts making copies.

When the copy job is finished, remove originals and copies.

Press the

{{{{

Interrupt

}}}}

key again.

The Interrupt indicator goes out.

When the display prompts you, place the remaining originals again be-
fore interrupting.

Press the

{{{{

Start

}}}}

key.

When the machine continues copying

Place the originals you want to copy.

Press the

{{{{

Start

}}}}

key.

The machine stops the other job and starts copying the new original.

BelliniC2_GBcopy_F_FM.book Page 23 Wednesday, December 11, 2002 3:47 PM

Summary of Contents for Aficio 9005


















































































































































































Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands

Nashuatec Aficio 9005, Operating Instructions Manual

Search results

Summary of Contents for Aficio 9005

Reviews:

Related manuals for Aficio 9005

Brands by name

Popular brands