MTU 20 V 4000 L63 Operating Instructions Manual Download Page 85

Page: 85 / 185

153116 – Knock Sensor Error A6

Red alarm. Initiated by antiknock control.

Cause

Corrective action

No signal received from this

knock sensor.

1. Check cabling.

2. Check sensor (tightening torque, damage), replace as

necessary.

153117 – Knock Sensor Error A7

Red alarm. Initiated by antiknock control.

Cause

Corrective action

No signal received from this

knock sensor.

1. Check cabling.

2. Check sensor (tightening torque, damage), replace as

necessary.

153118 – Knock Sensor Error A8

Red alarm. Initiated by antiknock control.

Cause

Corrective action

No signal received from this

knock sensor.

1. Check cabling.

2. Check sensor (tightening torque, damage), replace as

necessary.

153119 – Knock Sensor Error A9

Red alarm. Initiated by antiknock control.

Cause

Corrective action

No signal received from this

knock sensor.

1. Check cabling.

2. Check sensor (tightening torque, damage), replace as

necessary.

153120 – Knock Sensor Error A10

Red alarm. Initiated by antiknock control.

Cause

Corrective action

No signal received from this

knock sensor.

1. Check cabling.

2. Check sensor (tightening torque, damage), replace as

necessary.

153121 – Knock Sensor Error B1

Red alarm. Initiated by antiknock control.

Cause

Corrective action

No signal received from this

knock sensor.

1. Check cabling.

2. Check sensor (tightening torque, damage), replace as

necessary.

MS150059/01E 2012-07 | Troubleshooting | 85

TIM-ID: 0000017543 - 001

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands