MTU 20 V 4000 L63 Operating Instructions Manual Download Page 152

Page: 152 / 185

7.5 Gas System

7.5.1 Gas supply – Checking gas lines for leaks

Preconditions

☑ Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Leakage detection spray
Soap solution

WARNING

Natural gas is combustible.

Risk of fire and explosion!

• Avoid open flames, electrical sparks and ignition sources.

• Do not smoke.

Gas supply – Checking gas lines for leaks

Coat all connections of the gas supply line with soap solution or spray with leakage detection spray from

a distance of 30 to 50 cm.

• Leaks are indicated by the formation of bubbles or foam.

Replace leaking parts.

152 | Task Description | MS150059/01E 2012-07

TIM-ID: 0000004996 - 001

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands