MTU 20 V 4000 L63 Operating Instructions Manual Download Page 159

Page: 159 / 185

7.9 Coolant Circuit, General, High-Temperature Circuit

7.9.1 Engine coolant – Level check

Preconditions

☑ Engine is stopped and starting disabled.
☑ MTU Fluids and Lubricants Specification (A001061/..) is available.

WARNING

Coolant is hot and under pressure.

Risk of injury and scalding!

• Let the engine cool down.

• Wear protective clothing, gloves, and goggles / safety mask.

Engine coolant – Level check

Read off system pressure at pressure gauge, for system pressure (→ Product Summary - Technical Da‐

ta).

If required, top up with treated coolant (→ Page 163).

MS150059/01E 2012-07 | Task Description | 159

TIM-ID: 0000006768 - 001

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands