MTU 20 V 4000 L63 Operating Instructions Manual Download Page 157

Page: 157 / 185

7.7.3 Engine oil – Sampling and analysis

Preconditions

☑ MTU Fluids and Lubricants Specifications (A001061/..) are available.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

MTU test kit

5605892099/00

DANGER

Unguarded rotating and moving engine components.

Risk of serious injury – danger to life!

• Take special care when working on a running engine.

WARNING

Hot oil.

Oil can contain combustion residues which are harmful to health.

Risk of injury and poisoning!

• Wear protective clothing, gloves, and goggles / safety mask.

• Avoid contact with skin.

• Do not inhale oil vapor.

WARNING

Engine noise above 85 dB (A).

Risk of damage to hearing!

• Wear ear protectors.

Engine oil – Sample extraction and

analysis

Connect sampling hose (unit manufacturer

scope of delivery) to sampling neck (ar‐

rowed) with engine running at operating

temperature.

Drain approx. 0.5 liter engine oil into a

clean container.

Using the equipment and chemicals of the

MTU test kit, examine engine oil for:

• Dispersing capacity (spot test);

• Water content.

MS150059/01E 2012-07 | Task Description | 157

TIM-ID: 0000014117 - 001

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands