MTU 20 V 4000 L63 Operating Instructions Manual Download Page 165

Page: 165 / 185

7.10 Low-Temperature Circuit

7.10.1 Mixture coolant level - Check

Preconditions

☑ Engine shut down and starting disabled.
☑ MTU Fluids and Lubricants Specifications (A001061/..) are available.

WARNING

Coolant is hot and under pressure.

Risk of injury and scalding!

• Let the engine cool down.

• Wear protective clothing, gloves, and goggles / safety mask.

Checking mixture coolant level

Read off system pressure at pressure gauge, for system pressure (→ Product Summary - Technical Da‐

ta).

Top up with treated coolant as necessary (→ Page 168).

MS150059/01E 2012-07 | Task Description | 165

TIM-ID: 0000007032 - 002

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands