MTU 20 V 4000 L63 Operating Instructions Manual Download Page 151

Page: 151 / 185

7.4.4 Cylinder head cover – Removal and installation

Preconditions

☑ Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Gasket

(→ Spare Parts Catalog)

Removing cylinder head cover

Clean very dirty cylinder head covers (1)

prior to removal.

Remove spark plug connector

(→ Page 139).

Unscrew screws (2).

Remove cylinder head cover with gasket

from cylinder head.

Installing cylinder head cover

Clean mounting surface.

Check condition of gasket, replace if damaged.

Position gasket and cylinder head cover (1) on cylinder head.

Insert screws (2) in cylinder head cover and tighten them.

Note:

The locking plate must be removed from the cylinder head cover.

Install spark plug connector (→ Page 139).

MS150059/01E 2012-07 | Task Description | 151

TIM-ID: 0000029133 - 002

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands