MTU 20 V 4000 L63 Operating Instructions Manual Download Page 58

Page: 58 / 185

112413 – LO T-Exhaust B3

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112414 – LO T-Exhaust B4

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112415 – LO T-Exhaust B5

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112416 – LO T-Exhaust B6

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112417 – LO T-Exhaust B7

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

58 | Troubleshooting | MS150059/01E 2012-07

TIM-ID: 0000017543 - 001

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands