MTU 20 V 4000 L63 Operating Instructions Manual Download Page 114

Page: 114 / 185

189 – AL CAN2 Error Passive

ZKP-Number:

Yellow alarm.
Associated parameter 2.0500.689

Cause

Corrective action

CAN controller 2 has signaled a

warning. The cause may be e.g.

missing listening nodes, minor

malfunctions or temporary bus

overload.

Check operation of nodes (ECU, SAM or EMU) and cabling.

190 – AL EMU Parameter Not Supported

ZKP-Number:

Red alarm.
Associated parameter 2.0500.690

Cause

Corrective action

EMU parameters are not

supported.

Contact Service (configuration fault).

201 – SD T-Coolant

ZKP-Number:

Red alarm. Engine shutdown.
Associated parameter 1.8004.570

Cause

Corrective action

Coolant temperature sensor at

engine outlet defective, short

circuit or wire break.

Check sensor and cabling (B6.1), replace if necessary. Fault is

rectified when engine is restarted.

204 – SD Level Lube Oil

ZKP-Number:

Red alarm. Engine shutdown.
Associated parameter 1.8004.602

Cause

Corrective action

Engine oil level sensor defective,

short circuit or wire break.

Check sensor and cabling (B24), replace as necessary. Fault is

rectified when engine is restarted.

114 | Troubleshooting | MS150059/01E 2012-07

TIM-ID: 0000017544 - 001

Summary of Contents for 20 V 4000 L63


























































































































































































Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands

MTU 20 V 4000 L63, Operating Instructions Manual

Search results

Summary of Contents for 20 V 4000 L63

Reviews:

Related manuals for 20 V 4000 L63

Brands by name

Popular brands