Mitsubishi NZ2GF2B-60DA4 User Manual Download Page 17

Page: 17 / 174

CHAPTER 1 D/A CONVERTER MODULE

1.1 Application

CHAPTER 1

D/A CONVERTER MODULE

This chapter describes the applications and features of the D/A converter module.

1.1

Application

This module converts the digital data to the analog signal and outputs it to the external devices.

The digital data is set from the master station.
The D/A converter module enables works as follows.

The flow and temperature can be controlled from the master station by using the D/A converter module.

Digital signal (discrete signal)

Digital to analog

conversion

Analog signal (continuous signal)

Master station

CC-Link IE Field Network

D/A converter module

Control valve

Flow control

Tank

Master station

CC-Link IE Field Network

D/A converter module

Power conditioner

Heater

Summary of Contents for NZ2GF2B-60DA4















































































































































































Search results

Summary of Contents for NZ2GF2B-60DA4

Reviews:

Related manuals for NZ2GF2B-60DA4

Brands by name

Popular brands

Mitsubishi NZ2GF2B-60DA4, User Manual

Search results

Summary of Contents for NZ2GF2B-60DA4

Reviews:

Related manuals for NZ2GF2B-60DA4

Brands by name

Popular brands