background image

146

(10)Alert output setting (address: 0105

H

)

The alert output enable/disable status is set for each channel.

(a) Enabling the setting

Turn on and off Initial data setting request flag (RY9).

(b) Default value

The default value is set to Disable (1) for all channels.

(11)CH

†

 Alert output upper limit value (address: 0106

H

, 0108

H

, 010A

H

, 010C

H

),

CH

†

 Alert output lower limit value (address: 0107

H

, 0109

H

, 010B

H

, 010D

H

)

The upper and lower limit values of the alert output range are set.
For details on the alert output function, refer to the following.

 • Alert Output Function (

Page 92, Section 8.9)

(a) Setting range

 • Setting range: -32768 to 32767
 • The value to be set must satisfy the condition of Alert output upper limit value > Alert output lower limit 

value. An error occurs in a channel for which the setting not satisfying the condition is set. The error code 
(062

†

H

) is stored in Latest error code (RWr0), Error flag (RXA) turns on, and the ERR. LED turns on.

 • If the scaling function or shift functions is used, an alert target is the digital value where the operation of 

each function is reflected. Set the digital value considering the operation result of the function.

 • If Disable (1) is set to Alert output setting (address: 0105

H

), the settings of CH

†

 Alert output upper limit 

value (address: 0106

H

, 0108

H

, 010A

H

, 010C

H

) and CH

†

 Alert output lower limit value (address: 0107

H

0109

H

, 010B

H

, 010D

H

) are ignored.

(b) Enabling the setting

Turn on and off Initial data setting request flag (RY9).

(c) Default value

The default value is set to 0 for all channels.

Because the default value is set to 0, change the setting value when using the alert output function.

Data for b4 to b15 are fixed to "0".

b0

b15 b14 b13 b12 b11 b10 b9

b8

b7 b6

b5

b4

b3

b2

b1

0

0

0

0

0

0

0

0

0

0

0

0

CH3

CH4

CH2 CH1

0: Enable 
1: Disable

Summary of Contents for NZ2GF2B-60DA4















































































































































































Reviews: