manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R16MTCPU, Programming Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R16MTCPU Programming Manual Download Page 436

434

7  AUXILIARY AND APPLIED FUNCTIONS
7.5  Speed-Torque Control

■

Operation for "Position control mode 

 torque control mode switching"

When the mode is switched from position control mode to torque control mode, the command torque immediately after 
switching is the torque set in "torque initial value selection at control mode switching".

When the servo parameter "POL reflection selection at torque control (PC29)" is set to "0: Valid" and "Torque 
initial value selection at control mode switching" is set to "1: Feedback torque", a warning (error code: 0A55H) 
will occur at control mode switching, and the command value immediately after switching is the same as the 
case of selecting "0: Command torque". If the feedback torque is selected, set "1: Invalid" in the servo 
parameter "POL reflection selection at torque control (PC29)".

When the mode is switched from torque control mode to position control mode, the command position immediately after 
switching is the current feed value at switching.
The following chart shows the operation timing.

Torque initial value selection at 
control mode switching

Command torque to servo amplifier immediately after switching from position control mode 
to torque control mode

0: Command torque

Immediately after switching the control mode, the value of torque command device is the torque to servo amplifier 
regardless of the command torque time constant.

1: Feedback torque

Motor current value received from servo amplifier at switching is the torque to servo amplifier.

t

Torque

0

20.0%

30.0%

Position control mode

Position control mode

Torque control mode

Control mode switching
request device

Control mode setting device

0

Torque command device

0

200

300

0

0

50000

[0, 0]

[0, 1]

[0, 0]

OFF

ON

6 to 11ms

6 to 11ms

[St.1040] Start accept flag
(R: n/Q: M2001+n)

Speed command device
(Speed limit command value)

Control mode (b2, b3)
([Md.108] Servo status1
(R: 48n/Q: #8010+20n))

OFF

ON

20: Torque control mode

0: Position control mode

Summary of Contents for MELSEC iQ-R16MTCPU



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands