Mitsubishi Electric F720PJ-11KF, Manual

Page: 30 / 96

30
RS-485 communication
338
Communication operation command
source
0, 1 1 0 52
339
Communication speed command
source
0 to 2 1 0 52
340 Communication startup mode selection 0, 1, 10 1 0 43
342
Communication EEPROM write
selection
0, 1 1 0 45
343 Communication error count — 1 0 45
— 374 Overspeed detection level 0 to 400Hz, 9999 0.01Hz 9999
52
Second motor
const
ant
450 Second applied motor 0, 1, 9999 1 9999 41
Remote
Output
495 Remote output selection 0, 1, 10, 11 1 0 52
496 Remote output data 1 0 to 4095 1 0 52
— 502 Stop mode selection at communication error 0 to 3 1 0 45
Maintenance
503 Maintenance timer 0 (1 to 9998) 1 0 52
504 Maintenance timer alarm output set time 0 to 9998, 9999 1 9999 52
— 505 Speed setting reference 1 to 120Hz 0.01Hz 60Hz 37
Commu
nication
549 Protocol selection 0, 1 1 0 45
551
PU mode operation command source
selection
2, 4, 9999 1 9999 52
— 552 Frequency jump range 0 to 30Hz, 9999 0.01Hz 9999 37
PID
opera
tion
553 PID deviation limit 0 to 100%, 9999 0.1% 9999 47
554 PID signal operation selection 0 to 3, 10 to 13 1 0 47
C
urr
ent aver
age
time monitor
555 Current average time 0.1 to 1s 0.1s 1s 53
556 Data output mask time 0 to 20s 0.1s 0s
53
557
Current average value monitor signal
output reference current
0 to 500A 0.01A
Rated
inverter
current
53
— 561 PTC thermistor protection level 0.5 to 30k

, 9999 0.01k

9999
34
— 563 Energization time carrying-over times (0 to 65535) 1 0 38
— 564 Operating time carrying-over times (0 to 65535) 1 0
38
— 571 Holding time at a start 0 to 10s, 9999 0.1s 9999 34
PID
operat
ion
575 Output interruption detection time 0 to 3600s, 9999 0.1s 1s 47
576 Output interruption detection level 0 to 400Hz 0.01Hz 0Hz 47
577 Output interruption cancel level 900 to 1100% 0.1% 1000% 47
— 611 Acceleration time at a restart 0 to 3600s, 9999 0.1s 9999 39
— 653 Speed smoothing control 0 to 200% 0.1% 0% 53
— 665 Regeneration avoidance frequency gain 0 to 200% 0.1% 100% 53
— 779
Operation frequency during
communication error
0 to 400Hz, 9999 0.01Hz 9999 45
— 791 Acceleration time in low-speed range 0 to 3600s, 9999 0.1s 9999
34
— 792 Deceleration time in low-speed range 0 to 3600s, 9999 0.1s 9999 34
— 799 Pulse increment setting for output power
0.1kWh, 1kWh, 10kWh,
100kWh, 1000kWh
0.1kWh 1kWh 54
— 800 Control method selection 9, 30 1 30 54
Func-
tion
Parameter Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting