Mitsubishi Electric BAC-HD150 Instruction Book Download Page 31

Page: 31 / 48

- 31 -

7.2

Preparation for on-site adjustment

Have the following tools and documents ready before performing on-site adjustment and a test run.

Item

Description

Notes

Reference

Air conditioning control system diagram

Group configuration, IP address, Control item, and
etc.

Instruction Book that came with BAC-HD150

(This document)

Instruction Book that came with Setting Tool
BAC-HD150 Installation Manual
Relevant air-conditioner and controller’s
Instructions Books and Installation Manuals

Miscellaneous

BACnet

device list Documents related to

notification items, destinations, and methods.

Tools and parts

Computer

For Setting Tool

USB memory

For setting data backup

Installation CD for the Setting Tool

Setup disk

HUB

For connection to Setting Tool

Two LAN cables (category 5 or above) (straight cable)

For connection to Setting Tool

General tools such as a driver
Tester

Use to check wiring and voltage.

Miscellaneous

HUB

BACnet

LAN1

M-NET

BAC-HD150

Step-1

Step-4

Step-2

Step-3

BMS

Outdoor unit

Indoor unit

ME remote controller

LOSSNAY

System controller

WT05542X04.book Page 31 Wednesday, July 3, 2013 12:13 PM

Summary of Contents for BAC-HD150

















































Search results

Summary of Contents for BAC-HD150

Reviews:

Related manuals for BAC-HD150

Brands by name

Popular brands

Mitsubishi Electric BAC-HD150, Instruction Book

Search results

Summary of Contents for BAC-HD150

Reviews:

Related manuals for BAC-HD150

Brands by name

Popular brands