Miele HG05 Operating Instructions Manual Download Page 81

Page: 81 / 116

Problem solving guide

Noises

Problem

Possible cause and remedy

Knocking noise in the
wash cabinet.

A spray arm is knocking against an item in a basket.



Interrupt the programme, and rearrange the items
which are obstructing the spray arm.

Rattling noise in the
wash cabinet.

Items of crockery are insecure in the wash cabinet.



Interrupt the programme, and rearrange the items
of crockery.

A foreign object (e.g. a cherry stone) has become
lodged in the drain pump.



Remove the foreign object from the drain pump
(see "Maintenance - Cleaning the drain pump and
non-return valve").

Knocking noise in the
water pipes.

This may be caused by the on-site installation or the
cross-section of the piping.



This has no influence on dishwasher function. If in
doubt, contact a suitably qualified plumber.

Summary of Contents for HG05





















































































































Search results

Summary of Contents for HG05

Reviews:

Related manuals for HG05

Brands by name

Popular brands

Miele HG05, Operating Instructions Manual

Search results

Summary of Contents for HG05

Reviews:

Related manuals for HG05

Brands by name

Popular brands