background image

Cleaning and care

70

Cleaning the door front

Soiling that is left too long might

become impossible to remove and
could cause external surfaces to alter
or discolour.
Remove any soiling immediately.

Clean the front with a solution of
warm water and a little washing-up
liquid applied with a soft sponge.
Wipe the surfaces dry using a soft
cloth.
For cleaning, you can also use a
clean, damp microfibre cloth, such as
the Original Miele all purpose
microfibre cloth, without any cleaning
agent.

To avoid damaging external surfaces,
do not use:

– cleaning agents containing soda,

ammonia, acids or chlorides,

– cleaning agents containing descaling

agents,

– abrasive cleaning agents, e.g.

powder cleaners and cream cleaners,

– solvent-based cleaning agents,

– stainless steel cleaning agents,

– dishwasher cleaner,

– oven cleaner,

– glass cleaning agents,

– hard, abrasive brushes or sponges,

e.g. pot scourers, brushes or
sponges which have been previously
used with abrasive cleaning agents,

– dirt erasers,

– sharp metal scrapers,

– steel wool or metal scourers,

– steam cleaning appliances.

Summary of Contents for HG05





















































































































Reviews: