Miele HG05 Operating Instructions Manual Download Page 53 | Manualshive

Page: 53 / 116

background image

Operation

53

Starting the programme



Press the

Start

sensor.

The programme starts, and the prompt

Crockery can be added

appears in the

display.
As long as this prompt is showing,
crockery can be added without
compromising the wash results.



Water in the dishwasher may be

hot. Danger of scalding from water in
the cabinet.
Make sure you open the door very
carefully.

A programme should only be
cancelled in the first few minutes, if
at all. Otherwise important
programme stages could be omitted.

Time display

The estimated duration of the
programme selected appears in hours
and minutes in the display before the
programme begins. During the
programme, the time left until the end of
the programme is displayed.

Each programme stage is indicated by
a symbol:



Pre-wash / Soak



Main wash



Interim rinse



Final rinse



Drying



Finish

The programme duration displayed may
vary with the same programme. It is
influenced by, among other things, the
water temperature at each intake, the
reactivation process, the water softener,
the type of detergent, the amount of
crockery and how dirty it is.

When a programme is selected for the
first time, the display will show the
average programme duration for a cold
water intake.

The times shown in the Programme
chart refer to standard test loads and
temperatures.

Each time a programme is run, the
electronic unit takes the new conditions
into account, and calculates the time
required.

«
...
51
52
53
54
55
...
»

Summary of Contents for HG05





















































































































Reviews:

No comments

Related manuals for HG05

Brand: Malber Pages: 16

Brand: Labconco Pages: 72

Brand: TONG YANG MAGIC Pages: 46

Brand: UNITED Pages: 80

Brand: INVENTOR Pages: 68

Brand: Porter & Charles Pages: 27

Brand: Philco Pages: 132

Brand: VOX electronics Pages: 188

Brand: Hotpoint Ariston Pages: 24

Brand: John Lewis Pages: 32

Brand: Hotpoint Pages: 2

Brand: GE Pages: 16

Brand: GE Pages: 3

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 19

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands