background image

  IMPORTANT SAFETY INSTRUCTIONS

Keep all detergents and rinse aids
out of the reach of children.

Dishwasher detergents contain So-
dium Silicate and Sodium Carbo-

nate. In case of eye contact, immediate-
ly flush with water. Call a physician or
poison control.

Do not tamper with the 
controls.

Do not drink the water from the
wash cabinet.

When loading items to be 
washed:

– Locate pointed items so that they are
  not likely to damage the door seal.
– Load knives with the cutting edge

down to reduce the risk of injuries.

Do not wash plastic items unless
they are labeled “dishwasher safe”

or the equivalent. For items not labeled,
check the manufacturer’s recommenda-
tions.

Do not abuse, sit, or stand on the
door or dishracks of the dish-

washer.

Remove the front door and cut off
the power cord of the dishwasher

before removing it from service or dis-
carding it. This will help protect child-
ren from injury and accidentally locking
themselves in.

Under certain conditions, hy-
drogen gas may be produced in a

hot water system that has not been
used for two weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the
hot water system has not been used for
such a period, turn on all hot water
faucets and let the water flow from
each for several minutes before using
the dishwasher. This will release any ac-
cumulated hydrogen gas. Do not
smoke or use an open flame during this
time.

For safety reasons do not operate
this appliance on an extension

cable. Danger of overheating.

A damaged appliance is dan-
gerous. Switch off the mains and

call the Service Departement for assist-
ance.

Dishwashers with heating element

Do not touch the heating element
during or immediately after use.

SAVE THESE INSTRUCTIONS

7

Summary of Contents for G 879 SCVI













































































Reviews: