Miele G 879 SCVI Operating And Installation Instructions Download Page 23 | Manualshive

Page: 23 / 76

background image

Coffee bar.

Place coffee mugs on top of the bar so
that they sit at a slant. This allows all
water to run off the base of the mug.
The bar can also be used as a seper-
ator between two rows of glasses keep-
ing them from leaning against each
other. This protects the glasses and en-
sures good wash results. For wide
items, flip the bar over to the right.

Adjustable cup racks.

To make room for tall glasses, raise the
rack upwards. Lower it to double stack
smaller items.

Insert for glasses

The glassware insert can be installed in
the left or right side of the bottom bas-
ket in place of the removable plate in-
sert.

Very tall glasses can then be loaded
vertically so that they are washed more
effectively.

Loading the dishwasher

23

«
...
21
22
23
24
25
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: Jackson Pages: 2

Brand: Zanussi Pages: 3

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 24

Brand: Zanussi Pages: 16

WA422PRHD Series

Brand: Samsung Pages: 36

Brand: Maidaid Halcyon Pages: 17

Brand: Jenn-Air Pages: 14

Brand: GE Pages: 20

Brand: Asko Pages: 16

Brand: ZANKER Pages: 9

Brand: arcelik Pages: 24

Brand: Fisher & Paykel Pages: 76

Brand: Crest Audio Pages: 47

Brand: Crystal Pages: 38

Brand: AEG Pages: 28

FAVORIT 65020 M0P

Brand: AEG Pages: 64

FAVORIT 56602 ID0P

Brand: AEG Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands