Miele G 879 SCVI Operating And Installation Instructions Download Page 62 | Manualshive

Page: 62 / 76

background image

8. Securing the dishwasher

to the countertop.

Push the dishwasher back into the re-
cess.

Close the door and align the top of
door (control panel) with the cabi-
netry.

Open the door and check the verti-
cal gap, left and right side of top cor-
ners of wash cabinet. If distance to
side walls of cabinetry is not even,
push the dishwasher sideways to
align.

Close the door, check the alignment
of control panel again, correct if
necessary and repeat the inspection
of vertical gaps.

When correctly aligned, turn 2
1.3 cm (1/2") stainless steel screws
(supplied) into the prepared holes in
top edge as shown below.

The weight of the machine must be
supported by the legs, not the
countertop fastening screws. If se-
curing the top takes weight off of
the legs, extend the legs further
until they are tight against the floor.

Ensure that the seal on the top
edge of the dishwasher fits directly
against the worktop. If this is not the
case, adjust the height screws
more, (see Step 3).

Do not drill any additional holes
through any portion of the wash
cabinet. If in doubt about how to se-
cure the dishwasher, please call the
Miele Service Department.

Dishwasher installation

62

«
...
60
61
62
63
64
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: Jackson Pages: 2

WF501ANW Trouble Shooting Guide

Brand: Samsung Pages: 132

Brand: Hoover Pages: 28

Brand: Majestic Appliances Pages: 29

Brand: Philco Pages: 128

Brand: Admiral Pages: 6

Brand: Progress Pages: 72

Brand: Gorenje Pages: 35

MVWC300VW - Centennial Washer

Brand: Maytag Pages: 20

Brand: Ardo Pages: 14

Brand: AEG Electrolux Pages: 108

Brand: Asko Pages: 24

Brand: Hotpoint Ariston Pages: 24

Brand: Daewoo Pages: 46

Brand: Samsung Pages: 48

Brand: Samsung Pages: 73

Brand: Samsung Pages: 76

Brand: Samsung Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands