Miele G 879 SCVI Operating And Installation Instructions Download Page 53 | Manualshive

Page: 53 / 76

background image

Installing the slides.

Two slides are included and should be
installed on the feet of the dishwasher
before the machine is pushed under
the countertop. They will allow the ma-
chine to slide easier, protect the floor,
and allow adjustment of the rear level-
ing legs from the front of the machine.

Adjust the height manually before in-
stalling the dishwasher. Leave a
space of approx. 5 mm (3/16") below
the countertop to allow the dish-
washer to be pushed back easily
into the recess. Make sure the dish-
washer stands level.

Place the slides, with the ratchet at
the rear, onto the dishwasher legs.

If the legs of the machine extend
more than 2.5 cm (1") attach a piece
of wood under each slide skid for sta-
bility.

Pushing in the machine.

Push the machine into the opening,
making sure the electrical cable and
hoses can reach their connection
points without being kinked. Excess
hose should not be pushed behind
the dishwasher, but laid to the side.

VERY IMPORTANT!
Kinked hoses will cause the ma-
chine to malfunction.

Dishwasher installation

53

«
...
51
52
53
54
55
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: GE Pages: 2

Brand: Haier Pages: 6

Brand: Haier Pages: 12

Brand: Haier Pages: 34

Brand: Haier Pages: 12

Brand: Haier Pages: 11

Brand: Haier Pages: 28

Brand: Haier Pages: 12

Brand: Unimac Pages: 2

Brand: Jackson Pages: 2

Brand: Jackson Pages: 2

Brand: Jackson Pages: 2

Glasswashers Delta 5

Brand: Jackson Pages: 2

Brand: Hanseatic Pages: 72

Brand: Campomatic Pages: 36

Brand: Blomberg Pages: 40

Brand: NEFF Pages: 29

Brand: Fisher & Paykel Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands