Miele G 879 SCVI Operating And Installation Instructions Download Page 19 | Manualshive

Page: 19 / 76

background image

Pour liquid rinse aid into the storage
container until it is visible on the sur-
face of the screen. Do not add any
more rinse aid until the

H

indicator

lamp comes on.

Only use rinse aid specifically
labeled for residential dishwashers.
Inadvertently using powder or liquid
detergents will damage the rinse
aid dispenser.

Close the flap firmly. The flap must
audibly engage, otherwise water
could get into the rinse aid storage
container during the programme.

Wipe up any spilled rinse aid. This
prevents over-foaming occuring
during the next programme.

The flap should remain closed during
normal operation.

Setting the dosage.

The dosage selector comes factory set
to 3. The setting dispenses approxi-
mately 3 ml rinse aid per programme. It
can be adjusted from 1 to 6, depend-
ing on your requirements. It is best to
use the lowest setting that will still give
good results for your water supply.

If spots appear on dry glassware,
use a higher setting.

If streaking appears on dishes or
glasses, use a lower setting.

Adding rinse aid

19

«
...
17
18
19
20
21
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: Kalamazoo Pages: 40

Brand: NEFF Pages: 52

Brand: Hotpoint Pages: 48

Brand: Indesit Pages: 84

Brand: Hoover Pages: 17

Brand: Furrion Pages: 26

Brand: Alliance Laundry Systems Pages: 19

Lavadora y Secadora EWY8614W

Brand: EAS Electric Pages: 62

Brand: Fisher & Paykel Pages: 6

Brand: Smeg Pages: 28

Brand: Gaggenau Pages: 24

Brand: Zanussi Pages: 36

Brand: Zanussi Pages: 32

Brand: UNITED Pages: 32

Brand: Samsung Pages: 44

Brand: Samsung Pages: 48

WA13J571 Series

Brand: Samsung Pages: 44

Brand: Goddess Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands