Miele G 879 SCVI Operating And Installation Instructions Download Page 31 | Manualshive

Page: 31 / 76

background image

Interrupting a programme.

A programme can be interrupted by
opening the door.
If the door is once again closed, the
programme will continue from the point
of interruption.

Warning!
The water in the dishwasher may
be hot, and steam may be present!
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. The danger
of burns and scalding exists.
Once opened, close the door
nearly fully and allow 20-30 sec-
onds for the internal temperature
to equalize before shutting it com-
pletely.

Changing a programme.

A programme can only be changed be-
fore the door is closed. If a programme
has already started, turn off the dish-
washer, and re-select a programme.

Turning the dishwasher off.

At the end of a programme:

Open the door slightly. The indicator
lamp in the programme touch pad
will go out.

If the programme indicator lamp is
still lit, the programme has not yet
finished. Close the door to allow the
programme to finish.

Press the “O” (OFF) touch pad (19).
The indicator lamp will go out.

Open the door completely and un-
load the dishwasher (see “Unloading
the dishwasher”).

Close the door.

If the dishwasher will not be used for
an extended period of time,

Turn off the water valve.

Operating the dishwasher

31

«
...
29
30
31
32
33
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: Samsung Pages: 112

Brand: Kaiser Pages: 84

Brand: Hotpoint Pages: 48

Brand: Gaggenau Pages: 72

Brand: Maidaid Halcyon Pages: 17

Brand: Viking Pages: 12

Brand: GE Pages: 60

Brand: Asko Pages: 36

Brand: TONG YANG MAGIC Pages: 46

Brand: NEFF Pages: 31

Brand: Crest Audio Pages: 47

Brand: V-ZUG Pages: 60

Brand: Samsung Pages: 220

NA-S086M4 Series

Brand: Panasonic Pages: 33

Brand: Candy Pages: 17

Brand: GE Pages: 32

Brand: GE Pages: 16

Coin-Operated Commercial Tumble Action Washer

Brand: GE Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands