Miele G 879 SCVI Operating And Installation Instructions Download Page 57 | Manualshive

Page: 57 / 76

background image

Installing the bracket on the rear of
the custom door panel.

Push the dishwasher into its opening
and adjust the height.

Measure the distance “

X

” between

the round hole in the machine outer
door panel (shown in inset) and the
lower edge of the adjoining cabinet
door.

Place the door panel on a flat sur-
face, good side face down, being
careful not to scratch the surface.
Make certain that the bottom of the
panel is towards you.

Using a pencil, lightly draw a vertical
centerline on the panel (See the illus-
tration on the next page).

Draw a horizontal line “

X

” inches up

from the bottom edge of the panel.

For two-piece panels:

If your two-piece panel is joined
together using hardware that is not
flush with the rear of the panel, this
hardware must be removed before pro-
ceeding. The mounting bracket sup-
plied with the machine can be used to
secure both pieces to the dishwasher.

When mounting the two pieces,
make sure that the desired finished
panel height is maintained.

Dishwasher installation

57

«
...
55
56
57
58
59
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: Panasonic Pages: 21

Brand: Infiniton Pages: 127

Summit DW18SSADA

Brand: Accucold Pages: 2

Brand: Maytag Pages: 48

Brand: V-ZUG Pages: 36

Brand: Admiral Pages: 32

Brand: FAR Pages: 16

Brand: Supra Pages: 24

AdorinaWash V400

Brand: V-ZUG Pages: 20

Brand: Samsung Pages: 60

WA46CG3505A Series

Brand: Samsung Pages: 72

WA22M8700 Series

Brand: Samsung Pages: 96

WA50M7450A series

Brand: Samsung Pages: 132

WA47CG3500A Series

Brand: Samsung Pages: 216

WA48H7400A Series

Brand: Samsung Pages: 132

WA45n3050A Series

Brand: Samsung Pages: 204

Brand: Samsung Pages: 44

WF8804FS(A/F/G/H/S/V/W/Z)

Brand: Samsung Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands