Miele G 879 SCVI Operating And Installation Instructions Download Page 26 | Manualshive

Page: 26 / 76

background image

Adding detergent

Use only powder detergents formu-
lated for residential dishwashers
(for example, Electrasol

®

).

Do not

use gels or liquid detergents.

Press the latch on the detergent dis-
penser. The cover will spring open.

Fill the dispenser using approxi-
mately 20 - 25 ml (3/4 - 1 ounce) of a
quality powder detergent.

Close the cover. The cover will al-
ways be open at the end of a wash
programme.

Generally, filling the dispenser with
20 - 25 ml (3/4 - 1 ounce) of detergent
will be sufficient to ensure cleaning.

Do not exceed a maximum of 30 ml.

If you choose a programme utilizing the
pre-wash you will also need to put
detergent into the small compartment
labeled (I) in the center of the dispen-
ser.

Dishwasher detergents contain irri-
tant and corrosive ingredients. They
can cause burns in the mouth and
throat if swallowed, or inhibit brea-
thing. Keep children away from
detergent and from the dishwasher
when the door is open.

To avoid the danger of children com-
ing into contact with dishwasher
detergent, only fill the detergent dis-
penser immediately before starting
the programme.

Capacities:
Compartment I (pre-wash) takes a
maximum of 25 ml (1 oz). Compart-
ment II (main wash) has horizontal
marks to assist you in filling. The marks
indicate a level of approximately 20, 25
and 30 ml (3/4, 1 and 1 1/4 oz) respec-
tively.

Adding detergent

26

«
...
24
25
26
27
28
...
»

Summary of Contents for G 879 SCVI













































































Reviews:

No comments

Related manuals for G 879 SCVI

Brand: Haier Pages: 6

Brand: Haier Pages: 6

Brand: Haier Pages: 24

Brand: Haier Pages: 12

Brand: Haier Pages: 12

Brand: Haier Pages: 23

Brand: Haier Pages: 12

Brand: Danby Pages: 36

Brand: Midea Pages: 10

Brand: Asko Pages: 16

Brand: V-ZUG Pages: 116

Brand: Hotpoint Pages: 16

Brand: V-ZUG Pages: 64

DCS DishDrawer DD24DUT7

Brand: Fisher & Paykel Pages: 68

Brand: Hotpoint Pages: 10

Brand: Indesit Pages: 72

Brand: V-ZUG Pages: 84

Brand: Salora Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands