Miele G 6510 Operating Instructions Manual Download Page 99

Page: 99 / 104

Settings menu

Check filters

You can adjust the interval at which the

message to remind you to check the fil‐

ters appears.

You can set an interval of between 30

and 60 programme cycles.
The "Check filters" message is set at

the factory to appear after every 50 pro‐

gramme cycles.



Select the interval you want and con‐

firm this with

Soak

You can use this function to loosen

dried-on food residues in the pro‐

gramme selected.

Once activated, this function will be

carried out with all programmes until

you deactivate it.

If you are using powder dishwasher de‐

tergent, add approx. 5 g to compart‐

ment I.



Select the setting you want and con‐

firm with

Pre-wash

You can use this function to remove

easily loosened food residues in the

programme selected.

Once activated, this function will be

carried out with all programmes until

you deactivate it.



Select the setting you want and con‐

firm with

Brightness

There are seven different display bright‐

ness settings.



Select the brightness you want and

confirm this with

Version info

You can call up the electronic software

version of your dishwasher for technical

support purposes.



Confirm the display with

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands